European EMC Products Ltd POWER FILTERS Supplier of high performance and high power EMP Filters, Tempest Filters and Signal & Control Line Filters to the medical, defence, banking, telecommunications and datacentre sectors +44 (0)1799 523 073 [email protected] www.euro-emc.co.uk

EMP POWER FILTERS The purpose of EMP Protection is to prevent the electromagnetic pulses from high level nuclear weapons disrupting and destroying electronic equipment. To ensure compliance with the high international performance standards required to protect key infrastructure installations, our comprehensive range of EMP Filters have been designed in accordance with IEC 61000-4-24, severity levels 1 & 2, and can be readily upgraded to meet the design requirements of Mil-Std-188-125. Our standard EMP Power Filters are issued with a general electrical safety certificate per unit/batch which includes an Insertion Loss Test Certificate to 4GHz. MIL-STD EMP Power Filters come with an EU Declaration of Conformity and an Asymmetrical Insertion Loss (at 50 Ohm) Test Certificate can be issued upon request. All filters are produced in RAL 9016 traffic white, full gloss. We manufacture our filters in Configuration ‘C’ In Line Input/rear output, other configurations available upon request. Low Leakage filter options also available. STANDARD EMP POWER FILTER RANGE EEP Part No Current (A) Lines Voltage Hertz (HZ) Hemp Performance Insertion Loss Performance EEPF-16-2-PL 16A 2 240V 50/60Hz Designed in accordance (50 Ohm asymmetric, IEC CISPR17:2011) with IEC 61000-4-24, 80dB from 10MHz to 1GHz severity levels 1 & 2 EEPF-32-2-PL 32 A 2 240V 50/60Hz Designed in accordance (50 Ohm asymmetric, IEC CISPR17:2011) with IEC 61000-4-24, 80dB from 10MHz to 1GHz severity levels 1 & 2 EEPF-32-4-PL 32 A 4 415V 50/60Hz Designed in accordance (50 Ohm asymmetric, IEC CISPR17:2011) with IEC 61000-4-24, 80dB from 10MHz to 1GHz severity levels 1 & 2 EEPF-63-4-PL 63 A 4 415V 50/60Hz Designed in accordance (50 Ohm asymmetric, IEC CISPR17:2011) with IEC 61000-4-24, 80dB from 10MHz to 1GHz severity levels 1 & 2 EEPF-125-4-PL 125 A 4 415V 50/60Hz Designed in accordance (50 Ohm asymmetric, IEC CISPR17:2011) with IEC 61000-4-24, 80dB from 10MHz to 1GHz severity levels 1 & 2 EEPF-200-4-PL 200 A 4 415V 50/60Hz Designed in accordance (50 Ohm asymmetric, IEC CISPR17:2011) with IEC 61000-4-24, 80dB from 10MHz to 1GHz severity levels 1 & 2 EEPF-400-4-PL 400 A 4 415V 50/60Hz Designed in accordance (50 Ohm asymmetric, IEC CISPR17:2011) with IEC 61000-4-24, 80dB from 10MHz to 1GHz severity levels 1 & 2 MIL-STD EMP POWER FILTER RANGE EEP Part No Current (A) Lines Voltage Hertz (HZ) Hemp Performance Insertion Loss Performance EEPF-16-2-PL-MS 16A 2 240V 50/60Hz PCI requirements designed (50 Ohm asymmetric, IEC CISPR17:2011) in accordance with MIL-STD 80dB from 10MHz to 1GHz 188-125-1 EEPF-16-4-PL-MS 16A 4 415V 50/60Hz PCI requirements designed (50 Ohm asymmetric, IEC CISPR17:2011) in accordance with MIL-STD 80dB from 10MHz to 1GHz 188-125-1 EEPF-32-2-PL-MS 32 A 2 240V 50/60Hz PCI requirements designed (50 Ohm asymmetric, IEC CISPR17:2011) in accordance with MIL-STD 80dB from 10MHz to 1GHz 188-125-1 EEPF-32-4-PL-MS 32 A 4 415V 50/60Hz PCI requirements designed (50 Ohm asymmetric, IEC CISPR17:2011) in accordance with MIL-STD 80dB from 10MHz to 1GHz 188-125-1 EEPF-63-4-PL-MS 63 A 4 415V 50/60Hz PCI requirements designed (50 Ohm asymmetric, IEC CISPR17:2011) in accordance with MIL-STD 80dB from 10MHz to 1GHz 188-125-1 EEPF-125-4-PL-MS 125 A 4 415V 50/60Hz PCI requirements designed (50 Ohm asymmetric, IEC CISPR17:2011) in accordance with MIL-STD 80dB from 10MHz to 1GHz 188-125-1 EEPF-200-4-PL-MS 200 A 4 415V 50/60Hz PCI requirements designed (50 Ohm asymmetric, IEC CISPR17:2011) in accordance with MIL-STD 80dB from 10MHz to 1GHz 188-125-1 EEPF-400-4-PL-MS 400 A 4 415V 50/60Hz PCI requirements designed (50 Ohm asymmetric, IEC CISPR17:2011) in accordance with MIL-STD 80dB from 10MHz to 1GHz 188-125-1 +44 (0)1799 523 073 | [email protected] | www.euro-emc.co.uk

TEMPEST POWER FILTERS The purpose of Tempest power filter is to prevent eavesdropping of confidential information. Also with the increasing need to protect equipment housed within a shielded area from the damaging and disrupting effects of electromagnetic pulses and signals, as well as providing protection against surges produced from solar flares, nuclear weapons and lightning strikes, our uniquely designed range of modular filters ensure equipment is suitably protected at all times. European EMC Products Ltd supply a complete range of 2-Line/SP&N and 4-Line/TP&N TEMPEST power line filters. The standard range is 16A, 32A, 63A, 125A, 200A and 400A supporting facility compliance with the requirements of NATO standard SDIP-29, and equipment compliance with SDIP-27. Our standard Tempest Power Filters are issued with a general electrical safety certificate per unit/batch which includes an Insertion Loss Test Certificate to 4GHz. MIL-STD Tempest Power Filters come with an EU Declaration of Conformity and an Asymmetrical Insertion Loss (at 50 Ohm) Test Certificate can be issued upon request. All filters are produced in RAL 9016 traffic white, full gloss. We manufacture our filters in Configuration ‘C’ In Line Input/rear output, other configurations available upon request. Low Leakage filter options also available. STANDARD TEMPEST POWER FILTER RANGE EEP Part No Current (A) Lines Voltage Hertz (HZ) TEMPEST Performance EEPF-16-2-PL-TP 16A 2 240V 50/60HZ Shielding effectiveness performance designed in accordance with requirements of 60 and 100dB from 100kHz - 1GHz available as standard offerings* EEPF-32-2-PL-TP 32A 2 240V 50/60Hz Shielding effectiveness performance designed in accordance with requirements of 60 and 100dB from 100kHz - 1GHz available as standard offerings* EEPF-32-4-PL-TP 32A 4 415V 50/60Hz Shielding effectiveness performance designed in accordance with requirements of 60 and 100dB from 100kHz - 1GHz available as standard offerings* EEPF-63-4-PL-TP 63A 4 415V 50/60Hz Shielding effectiveness performance designed in accordance with requirements of 60 and 100dB from 100kHz - 1GHz available as standard offerings* EEPF-125-4-PL-TP 125A 4 415V 50/60Hz Shielding effectiveness performance designed in accordance with requirements of 60 and 100dB from 100kHz - 1GHz available as standard offerings* EEPF-200-4-PL-TP 200A 4 415V 50/60Hz Shielding effectiveness performance designed in accordance with requirements of 60 and 100dB from 100kHz - 1GHz available as standard offerings* EEPF-400-4-PL-TP 400A 4 415V 50/60Hz Shielding effectiveness performance designed in accordance with requirements of 60 and 100dB from 100kHz - 1GHz available as standard offerings* * Tailored performance requirements to 40GHz available on request. MIL-STD TEMPEST POWER FILTERS EEP Part No Current (A) Lines Voltage Hertz (HZ) TEMPEST Performance HEMP Performance EEPF-16-2-PL-TP-MS 16A 2 240V 50/60HZ Shielding effectiveness performance PCI requirements designed in designed in accordance with accordance with MIL-STD 188-125-1 requirements of 100dB from 100kHz to & DEF Stan 59-188 1GHz, and 60dB from 10GHz to 40GHz* EEPF-32-2-PL-TP-MS 32A 2 240V 50/60HZ Shielding effectiveness performance PCI requirements designed in designed in accordance with accordance with MIL-STD 188-125-1 requirements of 100dB from 100kHz to & DEF Stan 59-188 1GHz, and 60dB from 10GHz to 40GHz* EEPF-32-4-PL-TP-MS 32A 4 415V 50/60HZ Shielding effectiveness performance PCI requirements designed in designed in accordance with accordance with MIL-STD 188-125-1 requirements of 100dB from 100kHz to & DEF Stan 59-188 1GHz, and 60dB from 10GHz to 40GHz* EEPF-63-4-PL-TP-MS 63A 4 415V 50/60HZ Shielding effectiveness performance PCI requirements designed in designed in accordance with accordance with MIL-STD 188-125-1 requirements of 100dB from 100kHz to & DEF Stan 59-188 1GHz, and 60dB from 10GHz to 40GHz* EEPF-125-4-PL-TP-MS 125A 4 415V 50/60HZ Shielding effectiveness performance PCI requirements designed in designed in accordance with accordance with MIL-STD 188-125-1 requirements of 100dB from 100kHz to & DEF Stan 59-188 1GHz, and 60dB from 10GHz to 40GHz* EEPF-200-4-PL-TP-MS 200A 4 415V 50/60HZ Shielding effectiveness performance PCI requirements designed in designed in accordance with accordance with MIL-STD 188-125-1 requirements of 100dB from 100kHz to & DEF Stan 59-188 1GHz, and 60dB from 10GHz to 40GHz* EEPF-400-4-PL-TP-MS 400A 4 415V 50/60HZ Shielding effectiveness performance PCI requirements designed in designed in accordance with accordance with MIL-STD 188-125-1 requirements of 100dB from 100kHz to & DEF Stan 59-188 1GHz, and 60dB from 10GHz to 40GHz* *Specific performance requirements can be accommodated upon request. +44 (0)1799 523 073 | [email protected] | www.euro-emc.co.uk

TEMPEST PLUGGABLE FILTERS European EMC Products Ltd offer a range of Tempest pluggable power filters. Our selection of Tempest Pluggable Power Filters is made to both shield noise and assure compliance with the international performance standards necessary to safeguard critical infrastructure installations. The Tempest pluggable power filters are portable, versatile and are typically used in an IT environment protecting devices such as: Computers, Servers, Printers, Photocopiers etc. These filters are typically installed as a retrofit option where standard high performance TEMPEST filters cannot be installed in the existing infrastructure. Tempest pluggable filters are designed to meet IT equipment safety standard EN 60950-1. They have a fully 360⁰ screened input cable to maintain red/black separation to filter, Low Smoke Zero Halogen (LSZH) rated cabling for use in sensitive areas, High Common & Differential Mode Insertion Loss, Self-Healing Metallised Plastic Film Capacitors, Powder Coated Aluminium Enclosure. 13A designs of filter are downline tolerable to a personnel protection RCCD. EEP Part No Current (A) Hertz (HZ) Mains Plug Socket Socket Outlet Type Tempest Performance Type Outlet EEPF-06-1-PL-TP-PLG 6A 50/60Hz UK 1 (BS1363) Shielding effectiveness performance designed in accordance with requirements of 60dB from 100kHz to 1GHz EEPF-13-1-PL-TP-PLG 13A 50/60Hz UK 1 (BS1363) Shielding effectiveness performance designed in accordance with requirements of 60dB from 100kHz to 1GHz EEPF-06-2-PL-TP-PLG 6A 50/60Hz UK 2 (BS1363) Shielding effectiveness performance designed in accordance with requirements of 60dB from 100kHz to 1GHz EEPF-13-2-PL-TP-PLG 13A 50/60Hz UK 2 (BS1363) Shielding effectiveness performance designed in accordance with requirements of 60dB from 100kHz to 1GHz EEPF-32-2-PL-TP-PLG (CP) 32A 50/60Hz Commando 2 (BS1363) Shielding effectiveness performance Plug designed in accordance with requirements of 60dB from 100kHz to 1GHz EEPF-13-4-PL-TP-PLG 13A 50/60Hz UK 4 (BS1363) Shielding effectiveness performance designed in accordance with requirements of 60dB from 100kHz to 1GHz EEPF-32-4-PL-TP-PLG (CP) 32A 50/60Hz Commando 4 (BS1363) Shielding effectiveness performance Plug designed in accordance with requirements of 60dB from 100kHz to 1GHz EEPF-13-6-PL-TP-PLG 13A 50/60Hz UK 6 (BS1363) Shielding effectiveness performance designed in accordance with requirements of 60dB from 100kHz to 1GHz EEPF-16-6-PL-TP-PLG (CP) 16A 50/60Hz Commando 6 (BS1363) Shielding effectiveness performance Plug designed in accordance with requirements of 60dB from 100kHz to 1GHz EEPF-32-6-PL-TP-PLG (CP) 32A 50/60Hz Commando 6 (BS1363) Shielding effectiveness performance Plug designed in accordance with requirements of 60dB from 100kHz to 1GHz EEPF-16-2-PL-TP-PLG (EU) 16A 50/60Hz EU Plug 2 Schuko Shielding effectiveness performance designed in accordance with requirements of 60dB from 100kHz to 1GHz EEPF-16-4-PL-TP-PLG (EU) 16A 50/60Hz EU Plug 4 Schuko Shielding effectiveness performance designed in accordance with requirements of 60dB from 100kHz to 1GHz EEPF-15-2-PL-TP-PLG (US) 15A 50/60Hz US Plug 2 2 Pin Parallel Shielding effectiveness performance designed in accordance with requirements of 60dB from 100kHz to 1GHz +44 (0)1799 523 073 | [email protected] | www.euro-emc.co.uk

SIGNAL LINE & CONTROL LINE FILTERS SIGNAL LINE FILTER Our range of Signal Line Filters have been designed for Shielded Room requirements for attenuation of 60dB from 300 MHz –1 GHz. The filter will continue attenuating up to 30 GHz. Signal Filters are supplied in a compact sized format with current ratings up to 10 amp DC / 8 amp AC per phase. The filters are typically installed within Shielded Enclosures, IT Installations, Data Rooms, Military and Medical facilities. They are available in up to 12 line versions, however further versions are available on request. No. of Max Current Max AC Volt Max Typical Earth Storage Operating Temp Rise Termination Approximate Lines / Per Line Drop @ Full Load Voltages Voltage mA Temp Range Temp. @ Full Load Type Weight Per Line (Worst Case) AC DC AC STD 400 HZ 1-4 10A 8A 500mV 250V AC 1 4 -25 – +85°C -20 – +50°C <35°C M3 Thread 400g 4-8 10A 8A 500mV 250V AC 1 4 -25 – +85°C -20 – +50°C <35°C M3 Thread 800g 9-12 10A 8A 500mV 250V AC 1 4 -25 – +85°C -20 – +50°C <35°C M3 Thread 1200g CONTROL SIGNAL FILTER We offer a range of Control Line Filters which have been designed for maximum performance for Shielded Room applications. Shielded Rooms require high levels of attenuation to ensure no conducted/radiated emissions are either imported or exported from the room. The filters come in 2, 4, 8, 10 & 12-line formats, or as requested, and have a current rating of 500mA -3 Amps. Our Control Line filters are designed in accordance with MIL-STD 188-125-1. Rated Voltage AC: 250V AC, 50/60Hz Rated Voltage DC: 300V DC Rated Current: See table below Maximum Temperature Rise on Full Load: 25°C Operating Temperature: -20°C – + 50°C Storage Temperature: -25°C – + 85°C Insulation Resistance: >100MΩ Discharge Resistors: Internally fitted from line to case Discharge Time to Below 34V: <10 seconds Termination Types: Din Rail/Spindle Technical Specifications EEP Part No Lines Current (A) Rated Voltage (Max V) Weight EEPF-2-CLF 2 3.0 300 DC / 250 AC 3kg EEPF-4-CLF 4 2.0 300 DC / 250 AC 4kg EEPF-8-CLF 8 2.0 300 DC / 250 AC 8kg EEPF-10-CLF 10 2.0 300 DC / 250 AC 10kg EEPF-12-CLF 12 2.0 300 DC / 250 AC 12kg +44 (0)1799 523 073 | [email protected] | www.euro-emc.co.uk

About Us Established in 1996, European EMC Products Ltd (EEP) are an established British company whose experience and understanding of the science of shielding makes it an ideal partner in whom you can place your trust with confidence. The purpose of installing EEP shielding systems is to protect people and equipment against the threats posed by electromagnetic and radio frequency (RF) interference, radiation, magnetic fields and electromagnetic pulses. Our diverse range of turnkey products and services, including design, installation, project management, testing and consultancy are delivered across multiple sectors to an international client base. Security Doors Shielded Rooms Quench Pipes EMP Power Filters European EMC Products Limited are registered to BS EN ISO 9001:2015, Certificate Number FS38901. Registered Scope: The design, assembly, installation, servicing and testing of RF Shielded Structures and equipment including EMI Shielding, Blast Doors, Gas Tight Doors and specialised mobile Electromagnetic Pulse Protection (EMPP) containers. Radio Frequency, Magnetic Shielding and Quench systems for MRI (Magnetic Resonance Imaging) scanners. The design, assembly and installation of Ionising Radiation Protection facilities. The design, manufacture and installation of LED lighting systems for medical applications. European EMC Products Ltd can design, supply & install sound masking and eavesdropping protection systems that comply with all relevant standards. EEP Filters Limited are registered to BS EN ISO 9001:2015, Certificate Number FS38901. Registered Scope: The design, manufacture, management of installation and testing of high performance EMC and EMP Power and Data Line Filters. European EMC Products Ltd Units 7-9 Saffron Business Centre +44 (0)1799 523 073 Elizabeth Close, Saffron Walden [email protected] Essex, CB10 2NL, United Kingdom www.euro-emc.co.uk